• Register
Product Code: 1305-05017

Cat.6A Shielded Toolless Jack T568A/B

You Can Request Pricing By Building Up An RFP:
- +

PowerMAX+ Cat.6A Toolless Shielded Jack

DINTEK PowerMax+™ CAT.6A Fully shielded toolless horizontal keystone jack offers superior alien crosstalk suppression, excellent insertion loss, and provides enhanced electromagnetic interference (EMI) protection by utilizing robust die cast  zinc alloy connector body housing. The shielded connector is dual color coded for either 568A or 568B wiring schedules. 

Being specifically designed for high-speed data transmission, the DINTEK PowerMax+ CAT.6A Fully shielded toolless horizontal keystone jack is also backwards compatible with Shielded Cat.6 and Cat.5e systems.



  • Meet all requirements of ANSI/TIA-568-2.D for Cat.6A.
  • Draft ISO/IEC 11801 amendment 2,Category 6A
  • Draft ISO/IEC 60603-7
  • FTP 90° High density
  • Toolless, easy termination,no puch down tool needed.
  • Accept 22~24AWG, stranded or solid wire
  • Diecasting housing design.
  • Comply with FCC part 68 Subpart F and IEC 60603-7
  • Metalized cap design to reduce Alien cross talk
  • Wiring: T568A/B


  • 10GBASE-T Ethernet]
  • 100BASE-TX Fast Ethernet
  • 1000BASE-TX Gigabit Ethernet
  • 1000BASE-T Gigabit Ethernet
  • 10BASE-TX Ethernet
  • ATM CB1G
  • 155/622 Mbps ATM
  • 100 Mbps TP-PMD
  • 100VG-AnyLAN
  • 4/16 Mbps Token Ring
  • Voice

Standards Conformance

  • UL, C(UL), ETL Verified
  • ISO/IEC11801 2nd edition
  • ANSI/TIA Standard 568-2.D
  • CENELEC EN 50173

Ordering Information
Product NumberProduct NameOrientation


Std Pkg Qty


PowerMAX+ Cat.6A Toolless Shielded RJ45 Jack 



1pcs/PE Bag

Technical Specifications
Connector HousingHigh Impact Flame-Retardant Plastic
StandardUL94v-0 rated
Front Connection
Contact TypeSpring Wire
MaterialPhosphor Bronze Alloy Plated with 50 micro-inch of Gold over 70~100 micro-inch of Nickel
Rear Terminals
Terminal TypeIDC
MaterialPhosphor Bronze Alloy with 10 micro-inch 100% Sn Alloy
Physical Ranges
Temperature Range
Stroage-40 to +70℃
Operational-10 to +60℃
Relative humidity
OperationalMax. non-condensing 93%
Retention50N (11 Ibf) for 60s ± 5s
Insertion/Extraction life750 cycles minimum
Number of IDC terminations200 minimum

Plug retention force

Retention: 50N for 60sec.

Insulation Resistance500 mΩ min.@ 100V d.c
Dielectric Withstanding Voltage1000 V d.c. or a.c. Peak Contact to Contact @ 60 Hz for 1 MIN.
Spring Wire Contact Resistance20 mΩ Max.
Voltage/Current Rating150VAC/1.5A
IDC Contact Resistance2.5 mΩ Max.

Termination Demonstration

Strip 40mm of sheath from cable using stripper 

Roll back the braid or drain wire onto cable so it is out of the way.

Separate the four pairs and remove the foil wrap from around each pair.

Insert the wires through the back of the wire forming cap

Lay the wires into thier correct configuration, 

either T568A or T568B

Using side cutters, cut the wires level 

with the wire forming cap

Inset the wire forming cap into the rear of the 

jack body housing

Roll back the braid or drain wire so it will fit under the jack body. Close the rear covers, pressing firmly until the jaws close and click into place

The finished connector should not show any wires at the back, the jacket should reach to the rear of the connector and the braid or drain wire should be tidy underneath the shield body.

Stay Up To Date

Thanks for coming to use the services provided by logging in to the DINTEK website. Press the login button.

Once you are logged into the DINTEK Website. You will have access to additional content and services depending on the level of access that has been assigned to you.